Activity Stream - nScale.net

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs

Yesterday, 11:32 PM

P-LineSoo replied to a thread Walthers Walton and sons lumber in Structures & Scenery

Neat kit. Would fit nicely on my layout, may have to pick one up, John Boy!

8 replies | 425 view(s)

Yesterday, 10:32 PM

P-LineSoo replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

I have a reverse loop on my layout. It's on the innermost route on the old section, and it makes itself purposeful by following the industries next...

7 replies | 95 view(s)

Yesterday, 08:38 PM

BigLocosForMe replied to a thread Body mounting couplers on 89ft flatcars in Rollingstock

So the couplers I'm thinking to use are the ones that are currently on the cars:...

2 replies | 48 view(s)

Yesterday, 06:55 PM

WP&P replied to a thread Body mounting couplers on 89ft flatcars in Rollingstock

Even if the CA is successfully applied, I would worry about the long term viability of that approach. With the screw, all of the forces acting on the...

2 replies | 48 view(s)

Yesterday, 06:47 PM

WP&P replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

I personally don't think that reversing loops are actually all that necessary or desirable, though in my youth I certainly did whatever I could to...

7 replies | 95 view(s)

Yesterday, 06:20 PM

MRLdave replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

Nthebasement.....thanks for the idea, but your idea doesn't solve the shorting issue, which sends my base unit into alarm. The trucks on the Kato...

7 replies | 95 view(s)

Yesterday, 06:18 PM

donzi replied to a thread PICO N Scale 65 Ton Whitcomb in Diesel

Piko site shows available. Starting to hear rumors about the trucks...Appears only one truck is gear driven. GER: N Diesellokomotive Rh 600 NS III...

27 replies | 1173 view(s)

Yesterday, 06:05 PM

amstilost replied to a thread Question about Digitrax DT602D in DCC

I did happen to run across the 4.26 version of jmri while I was looking for my jmri manual download so I do have it. I have been in the updated...

26 replies | 337 view(s)

Yesterday, 04:39 PM

Stu replied to a thread Question about Digitrax DT602D in DCC

My question related to the version of JMRI, I went back and looked at the quote and my comment in #22. Good luck.

26 replies | 337 view(s)

Yesterday, 04:04 PM

amstilost replied to a thread Question about Digitrax DT602D in DCC

When it Crashed the first time I didn't have the opportunity to save it. I could have saved it before it crashed the second time but I didn't think...

26 replies | 337 view(s)

Yesterday, 03:57 PM

amstilost replied to a thread Question about Digitrax DT602D in DCC

I know this ended up not being at all about the Digitrax DT602D wireless remote and I apologize for that. So after the two crashes with JMRI I...

26 replies | 337 view(s)

Yesterday, 03:49 PM

Stu replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

Reverse loops make a LOT of sense for that type of operation AND your description of the room you have. I have two RLs and enjoy operating my layout...

7 replies | 95 view(s)

Yesterday, 03:32 PM

NtheBasement replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

Not sure what the geometry is with the wye but see if throwing it with a DPDT switch that controls polarity of some section of your layout would...

7 replies | 95 view(s)

Yesterday, 03:18 PM

amstilost replied to a thread Question about Digitrax DT602D in DCC

I know this ended up not being at all about the Digitrax DT602D wireless remote and I apologize for that. So after the two crashes with JMRI I...

26 replies | 337 view(s)

Yesterday, 02:11 PM

MRLdave replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

I'm struggling a bit with an auto reverse issue myself right now........on a wye, not a loop, but the principle is the same. The issue with the wye,...

7 replies | 95 view(s)

Yesterday, 01:32 PM

BigLocosForMe replied to a thread Welcome new nScale.net Members in General Rail Discussion

So an introduction is in order, apparently. I've been here before, but for some reason my previous login no longer works and I can't reset the...

5766 replies | 1001521 view(s)

Yesterday, 01:06 PM

DanB80 replied to a thread Reverse Loop in Layout Builds, Design, & Planning.

Usually its real estate, a reverse loop can take up a considerable amount of room compared to a turntable or the old 0-5-0. The bigger/longer your...

7 replies | 95 view(s)

Yesterday, 11:57 AM

majordadsage started a thread Reverse Loop in Layout Builds, Design, & Planning.

I have decided to go around the room with a 30" deep bench. The total length will be approximately 26'. I want to run the trains....I like the...

7 replies | 95 view(s)

Yesterday, 09:44 AM

BigLocosForMe started a thread Body mounting couplers on 89ft flatcars in Rollingstock

To try to improve the tracking of some Micro Trains 89ft flatcars I've got, I'm planning to remove the existing sort-of truck mounted couplers and...

2 replies | 48 view(s)

Yesterday, 05:24 AM

Comfortably numb replied to a thread A Change of Plans ! in Layout Builds, Design, & Planning.

And this makes 11. https://www.youtube.com/watch?v=tstz1x9hmXo

226 replies | 30338 view(s)

Yesterday, 12:08 AM

MRLdave replied to a thread Walthers Walton and sons lumber in Structures & Scenery

Looking at the kit, I wondered how a forklift would put lumber on the upper level. The bunks are perpendicular to the direction a forklift would be.

8 replies | 425 view(s)

1st Oct 2023, 11:49 PM

Stu replied to a thread Welcome new nScale.net Members in General Rail Discussion

Sorry to hear about your issue. Have you considered building a pre-designed track plan? I did, the Monopoly & Octopus from the Atlas Nine book,...

5766 replies | 1001521 view(s)