Search:

Type: Posts; User: Olie

Page 1 of 13 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Noob DCC question

    by Olie
    Replies
    31
    Views
    986

    The NCE Power Cab will work with DCC decoders and...

    The NCE Power Cab will work with DCC decoders and not limited to NCE brand. It is a complete starter kit so as long as it meets your layout needs, you can be up and running with just the kit. Here is...
  2. Replies
    294
    Views
    7,758

    Tony, I too ran into the same problem a while...

    Tony, I too ran into the same problem a while back with my tight radius loops. I had the same issue as aflica and was effecting the rail spacing. Have you run a gauge around that section?
  3. Replies
    185
    Views
    4,882

    TONY!!! I'm glad you and the Mrs are OK. You've...

    TONY!!! I'm glad you and the Mrs are OK. You've been missed and it's great to see you back.
  4. I actually did what is shown in the picture....

    I actually did what is shown in the picture. Works fairly well and no need to replace the coupler at all.
    104068
  5. Replies
    14
    Views
    636

    Good to hear Hobby Town was able to check it out...

    Good to hear Hobby Town was able to check it out for you. That really sucks you have to send it back in for work though. I don't have any N scale BLI locos, so I can't speak on those but I do have...
  6. It pops off like the front one. I have mine...

    It pops off like the front one. I have mine upside down right now and just used a small flat head screwdriver. Ran it along one side between the wheels and the bolster pin. Popped right off.
    104026
  7. Replies
    14
    Views
    636

    Hobby Town in Kennesaw is about 30 minutes from...

    Hobby Town in Kennesaw is about 30 minutes from you. It's the largest in the nation and they work on locomotives right there in the store. The guys I've talked to that work behind the counter have...
  8. Replies
    14
    Views
    636

    Do you know anyone with a DCC controller that can...

    Do you know anyone with a DCC controller that can set CV8 to 8?
  9. Replies
    14
    Views
    636

    The Paragon 3 sound system can be reset to the...

    The Paragon 3 sound system can be reset to the factory
    default by setting CV8 to a value of 8. If this cannot be
    accomplished, the system can be manually reset by
    holding down the tiny reset...
  10. Replies
    15
    Views
    531

    Looks great Mark. I'm always impressed with your...

    Looks great Mark. I'm always impressed with your builds.
  11. Replies
    34
    Views
    1,058

    Broken down fencing along the tracks?

    Broken down fencing along the tracks?
  12. Replies
    4
    Views
    341

    Amazon. I've gotten everything from 0-80 on up.

    Amazon. I've gotten everything from 0-80 on up.
  13. Oh man, I'm sorry you're having trouble. I should...

    Oh man, I'm sorry you're having trouble. I should have been more specific. I was referring to a cap added to the decoder as an aftermarket add-on. After reading your decoder information on the OP, I...
  14. I used the deep water pour for my layout and it...

    I used the deep water pour for my layout and it worked fairly well.
    103550
    103551
  15. Is there a capacitor wired in to the decoder? I...

    Is there a capacitor wired in to the decoder? I found on my loksound setups if I have a keep alive or capacitor wired in, I have problems programming with the lokprogrammer.
  16. Replies
    4
    Views
    411

    www.rslaserkits.com

    www.rslaserkits.com
  17. Replies
    16
    Views
    568

    Digi-key is where I get mine.

    Digi-key is where I get mine.
  18. Replies
    10
    Views
    649

    That is sad to hear, both for his wife and the...

    That is sad to hear, both for his wife and the business. I hope he finds peace.
  19. Replies
    22
    Views
    693

    What about using an iphone speaker? I've read a...

    What about using an iphone speaker? I've read a few places where the 6's speaker has been used with good results.
    https://www.ifixit.com/Store/iPhone/iPhone-6s-Loudspeaker/IF314-009?o=1
  20. Replies
    19
    Views
    574

    Well look at that. A comparison of BLMA to...

    Well look at that. A comparison of BLMA to FVM.....too bad we were talking about jpwisc comparison of FVM to FVM. I read that article before I made the thread. You've proved my point.

    Thanks all...
  21. Replies
    19
    Views
    574

    Why ASSUME I didn't? It gets really old...

    Why ASSUME I didn't? It gets really old constantly reading people butt in to conversation with comments like this one. Then you wonder why people stop posting......
  22. Replies
    19
    Views
    574

    Would you happen to have any pics showing the...

    Would you happen to have any pics showing the wide next to a standard size?
  23. Replies
    19
    Views
    574

    Just checked the FVM website and they are listing...

    Just checked the FVM website and they are listing the 3610 wide tread 36" .540" wheels in stock!!! I haven't seen the wide tread versus the standard but that is a good sign that they are receiving...
  24. Replies
    18
    Views
    827

    I use an old solder tube. Of course, I can't find...

    I use an old solder tube. Of course, I can't find it to post a pic of it but it's the tube with the red top and a hole in the middle to pull the solder through. Works great from pouring ballast of...
  25. Replies
    19
    Views
    574

    Have you ever compared them to the Rapido ones?

    Have you ever compared them to the Rapido ones?
Results 1 to 25 of 305
Page 1 of 13 1 2 3 4