Search:

Type: Posts; User: donzi

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    310

    Good Stuff.

    Good Stuff.
  2. Replies
    15
    Views
    310

    @Moose2013 The difficulties you’re...

    @Moose2013

    The difficulties you’re experiencing are somewhat typical of decal making for the first times.
    I’ve had the same ones when I first got into decal making.
    I now get very good results...
  3. Replies
    13
    Views
    249

    There is a recommended layout height, and that...

    There is a recommended layout height, and that height is whatever feels comfortable for you to operate.
    You state you will be sitting, 36” works when seated for me.
  4. Thread: Worm Gears

    by donzi
    Replies
    7
    Views
    273

    To remove a worm, I use @randgust...

    To remove a worm, I use @randgust method of a notch in a piece of plate steel and tap the motor shaft with a drift.
    To install a worm on a shaft, I usually put the worm in a cup of boiling water for...
  5. Degrease then lube.

    Degrease then lube.
  6. Thread: Remove grease

    by donzi
    Replies
    2
    Views
    178

    Elwood ...

    Elwood

    https://www.homedepot.com/p/CRC-QD-11-oz-Contact-Cleaner-02130-6/202262505
  7. Replies
    11
    Views
    367

    @DDavidsonFarms I have had very good results...

    @DDavidsonFarms
    I have had very good results from both the last two versions, with the addition of a Spectrum short tender.
    Manufacturing tolerances are sloppy, with the older versions.
    Somewhat...
  8. Replies
    1,116
    Views
    83,101

    @56Pontiac, Don’t know what all replies were...

    @56Pontiac,
    Don’t know what all replies were posted to your comment, but judging from the comments I can see, it appears that you pissed off Charlie’s Angles and the Groupie.
    Take advantage of the...
  9. What is amp draw at “defined and specific...

    What is amp draw at “defined and specific controller setting” for each lokie?
    Could be one thing, or could be several issues all contributing to the “cause”.
    I find with Bachmann, it’s usually the...
  10. Replies
    14
    Views
    567

    Hi TrainFreak, You state; I am assuming...

    Hi TrainFreak,

    You state;

    I am assuming this reading was under a “no load” condition? Correct?
    Was the lokie actually on the track making sounds when this reading was recorded? And at full...
  11. Replies
    56
    Views
    1,645

    Gunna have to say, natural disaster as well. Two...

    Gunna have to say, natural disaster as well.
    Two years ago if Irma would have passed West of me instead of East, at the same distance from the Eye, I don’t think this house would have survived....
  12. Agree with @randgust...

    Agree with @randgust
    The tighter the tolerance the more precise the mechanism.
    The looser, the more slop is introduced.
    The second is why some mechanisms need more “break in time” than others.
    A...
  13. Replies
    8
    Views
    508

    Inventory (money) sitting on the shelf for months...

    Inventory (money) sitting on the shelf for months or years, is money you don’t have access to for other things. That money earns no interest. It actually loses value.
    About 30+ years ago, someone...
  14. Replies
    10
    Views
    369

    He can't break it in, It won't run long enough, ...

    He can't break it in, It won't run long enough,
    Re-read his OP.
  15. Replies
    10
    Views
    369

    I think a wheel not firmly on the railhead may be...

    I think a wheel not firmly on the railhead may be your problem as well.
    Buy an “old school” feeler gauge from your local big box or an auto parts store.
    Place the lokie on a piece of glass (from a...
  16. Replies
    24
    Views
    802

    No need to wash or wipe anything, the degreaser...

    No need to wash or wipe anything, the degreaser evaporates off clean, but I do set the cleaned parts to dry on a paper towel.
    If you are unsure about getting everything back together properly then...
  17. Replies
    290
    Views
    41,837

    ...Imagine that... I read it on the internet,...

    ...Imagine that...

    I read it on the internet, therefore I know it's true.

    sheesh....

    Polar vs. non Polar ...YFKM
  18. Replies
    24
    Views
    802

    Hi AP, It’s very possible to “heavy” of an oil...

    Hi AP,

    It’s very possible to “heavy” of an oil was used to lubricate the lokie, or possibly some lubricant is passing though the bearings and settling on the commutator.
    When the oil heats up and...
  19. It’s very good. Not bashing, just trying to be...

    It’s very good.

    Not bashing, just trying to be constructive…
    I like the heavy rust on the cab and hood.
    But my eye expects to see that same level of weathering to the handrails and the...
  20. Replies
    11
    Views
    497

    IIRC, I am using an MT 2004. But that conversion...

    IIRC, I am using an MT 2004.
    But that conversion took place many years ago.
  21. Every steam locomotive Bachman has produced for...

    Every steam locomotive Bachman has produced for the last 13 years has received an A rating on the Spookshow site.
    One man’s opinion, so grain of salt and all that.
    A sample size of one or two from...
  22. Replies
    11
    Views
    529

    Yes that, or a smaller version beard/moustache...

    Yes that, or a smaller version beard/moustache trimmer.
  23. Replies
    19
    Views
    451

    ​ 5x loupe, Calipers.


    5x loupe, Calipers.
  24. Replies
    1
    Views
    313

    1015 at the correct height is an excellent...

    1015 at the correct height is an excellent choice.
    Not sure if possible, might need something off-set.
  25. Replies
    290
    Views
    41,837

    I know it’s true because I read it on the...

    I know it’s true because I read it on the internet.
    Propaganda for the uninformed, magazines have to be sold to stay alive.
    And Fugate will sell this issue, controversy sells.
    As have many here,...
Results 1 to 25 of 217
Page 1 of 9 1 2 3 4