Search:

Type: Posts; User: donzi

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    131

    He can't break it in, It won't run long enough, ...

    He can't break it in, It won't run long enough,
    Re-read his OP.
  2. Replies
    8
    Views
    131

    I think a wheel not firmly on the railhead may be...

    I think a wheel not firmly on the railhead may be your problem as well.
    Buy an “old school” feeler gauge from your local big box or an auto parts store.
    Place the lokie on a piece of glass (from a...
  3. Replies
    21
    Views
    434

    No need to wash or wipe anything, the degreaser...

    No need to wash or wipe anything, the degreaser evaporates off clean, but I do set the cleaned parts to dry on a paper towel.
    If you are unsure about getting everything back together properly then...
  4. Replies
    281
    Views
    39,572

    ...Imagine that... I read it on the internet,...

    ...Imagine that...

    I read it on the internet, therefore I know it's true.

    sheesh....

    Polar vs. non Polar ...YFKM
  5. Replies
    21
    Views
    434

    Hi AP, It’s very possible to “heavy” of an oil...

    Hi AP,

    It’s very possible to “heavy” of an oil was used to lubricate the lokie, or possibly some lubricant is passing though the bearings and settling on the commutator.
    When the oil heats up and...
  6. It’s very good. Not bashing, just trying to be...

    It’s very good.

    Not bashing, just trying to be constructive…
    I like the heavy rust on the cab and hood.
    But my eye expects to see that same level of weathering to the handrails and the...
  7. Replies
    11
    Views
    330

    IIRC, I am using an MT 2004. But that conversion...

    IIRC, I am using an MT 2004.
    But that conversion took place many years ago.
  8. Every steam locomotive Bachman has produced for...

    Every steam locomotive Bachman has produced for the last 13 years has received an A rating on the Spookshow site.
    One man’s opinion, so grain of salt and all that.
    A sample size of one or two from...
  9. Replies
    11
    Views
    423

    Yes that, or a smaller version beard/moustache...

    Yes that, or a smaller version beard/moustache trimmer.
  10. Replies
    19
    Views
    290

    ​ 5x loupe, Calipers.


    5x loupe, Calipers.
  11. Replies
    1
    Views
    228

    1015 at the correct height is an excellent...

    1015 at the correct height is an excellent choice.
    Not sure if possible, might need something off-set.
  12. Replies
    281
    Views
    39,572

    I know it’s true because I read it on the...

    I know it’s true because I read it on the internet.
    Propaganda for the uninformed, magazines have to be sold to stay alive.
    And Fugate will sell this issue, controversy sells.
    As have many here,...
  13. ;) Yes. You can make the gap whatever you...

    ;)

    Yes.

    You can make the gap whatever you want, use a credit card will get you close.
    If you want to be more accurate then check the NMRA.
    Start here;...
  14. Replies
    6
    Views
    220

    IMO Best way is a complete dis-assembly and...

    IMO Best way is a complete dis-assembly and de-grease.
    If you can’t do that then;
    Take it outside and use a disposable bowl (miracle whip) etc.Tupperware type but disposable.

    Then hose it...
  15. Replies
    30
    Views
    688

    There could be lots of reasons for de-railing...

    There could be lots of reasons for de-railing with Bachmann EZ turnouts (any other manufacturer as well).
    As suggested, start with wheel gauge, then track gauge.
    Both maybe correct and the cause is...
  16. Replies
    14
    Views
    934

    That MRC Tech IV 260 is way more than enough for...

    That MRC Tech IV 260 is way more than enough for N scale.
    Mine puts out 12v at about 60% throttle.
    I’ve run 7 Atlas GP9’s at the same time with it.
  17. I use this from Office Depot ...

    I use this from Office Depot
    https://www.officedepot.com/a/products/326307/Realspace-Clamp-On-Magnifier-Task-Lamp/

    I also use single eye loupes from Granger. 4x, 5x, and 10x....
  18. Replies
    66
    Views
    6,951

    Rasputen pm sent

    Rasputen pm sent
  19. Replies
    17
    Views
    260

    I think you have a wheel(s) leaving the railhead....

    I think you have a wheel(s) leaving the railhead.
    Those long diesels are notorious for that.
  20. Replies
    24
    Views
    590

    Kato wants your opinion yet again…VOTE!

    Kato wants your opinion yet again…VOTE!

    http://www.katousa.com/webpoll.html
  21. Replies
    252
    Views
    44,443

    Sticky: Very first locomotive scratch/bash done many...

    Very first locomotive scratch/bash done many moons ago, painted with a brush.
    It’s pure fantasy.
    Yes, it started life as Lima 2-6-4T.
    According to my inventory notes, last run was 12/04/2002.
    Got...
  22. Replies
    252
    Views
    44,443

    Sticky: https://i612.photobucket.com/albums/tt207/sandjamb...

    https://i612.photobucket.com/albums/tt207/sandjambag/Camelback/20190216_103342_zpsrlvz2k6n.jpg
    ...
  23. Replies
    12
    Views
    366

    There is lots of stuff in that black gunk....

    There is lots of stuff in that black gunk.
    Oxidation, residuals from vapors in the air (cooking,cleaning, aerosols), dust, dead skin, pet dander, rubber from traction tires,wheel plating wearing...
  24. Replies
    12
    Views
    349

    ]Haven't noticed loco reviews that comment on...

    ]Haven't noticed loco reviews that comment on pulling power. Why not?[/LEFT]


    Any professional machinist will tell you that no two identical parts are exactly alike.
    Same with automobiles one...
  25. Replies
    14
    Views
    331

    IIRC I used a font size 4 in MS Word for number...

    IIRC I used a font size 4 in MS Word for number board decals
Results 1 to 25 of 204
Page 1 of 9 1 2 3 4