Search:

Type: Posts; User: MRLdave

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. I don't pay any attention to the Horribly...

    I don't pay any attention to the Horribly oversized stuff, so can't really say what I'd want since I don't know what there is...….I'm probably better off that way.
  2. I used 5 packs on my last layout. I probably used...

    I used 5 packs on my last layout. I probably used the same Radio Shack rotary switch that WP used. It worked well, but you had to isolate both rails on each block. It also required A LOT of wire...
  3. RS2 is 4 axles,RSC2 is 6 axles...…..the chassis...

    RS2 is 4 axles,RSC2 is 6 axles...…..the chassis are identical and you can put either set of trucks on the chassis or 1 of each if you want. As Mark said, remove the shell and loosen the screws to...
  4. I've had relatively good luck with BLI......at...

    I've had relatively good luck with BLI......at least on diesels. Had one E6 that quit on me .....sent it in and it was repaired under warranty. I was told it was a board issue. So I took the plunge...
  5. Replies
    13
    Views
    432

    Kato is/was primarily a "japanese" manufacturer,...

    Kato is/was primarily a "japanese" manufacturer, making models of japanese trains........then they expanded into early (40s to 60s) American Passenger equipment, and more recently into large modern...
  6. Replies
    7
    Views
    260

    I'm not totally sure even the manufacturers have...

    I'm not totally sure even the manufacturers have a grasp on this. I have quite a few new cars (various manufacturers) that if I put any kind of pressure on the car when setting it on the track, the...
  7. Replies
    19
    Views
    382

    But if I'm actually fixing something, my set of...

    But if I'm actually fixing something, my set of small screwdrivers and my set of tweezers rarely leave the workbench.
  8. Replies
    19
    Views
    382

    I find a really big hammer makes a lot of my...

    I find a really big hammer makes a lot of my problems go away!
  9. Replies
    30
    Views
    833

    It's true that the track is likely the issue, but...

    It's true that the track is likely the issue, but you don't need to "dump" the Bachmann track. However you do need to understand the fact that the Bachmann track is not the route you want to go as...
  10. Replies
    30
    Views
    833

    I agree with the gauge answer. I've found that...

    I agree with the gauge answer. I've found that Bachmann locos can have issues on other brands of track......partly because they are set for Bachmann track. The E-Z track I have is all slightly wider...
  11. Replies
    11
    Views
    327

    Just looked at your picture closer........those...

    Just looked at your picture closer........those trucks have a little plastic cover that snaps on. So the procedure is snap the cover off, the coupler will then lift out (no twisting) , you slide the...
  12. Replies
    11
    Views
    327

    I've run into a few cases where the T-shank on...

    I've run into a few cases where the T-shank on the unimate is too tall for the socket on the truck. I've had to file a few down but it's a simple task. Other than that it's twist out /twist in. And...
  13. Replies
    1
    Views
    175

    Walthers SW1200

    Another DCC issue.....anyone have any experience with the new (last) run of DCC friendly LL/Walthers SW1200s? I bought it because it was supposed to be DCC friendly.....it was, up to a point. The...
  14. Replies
    5
    Views
    222

    Interesting thing...….a while back I needed a...

    Interesting thing...….a while back I needed a motor replaced, and Intermountain sent me 2 of the non-wired motors as replacements. I wonder if the issue wasn't on the DCC manufacturers...….maybe the...
  15. Replies
    5
    Views
    222

    Seems strange the board would move since it's...

    Seems strange the board would move since it's screwed down to the chassis.....which is not to say the motor couldn't move. As I was trying to figure this out, I discovered that the motors are...
  16. Replies
    5
    Views
    222

    2 unrelated DCC questions

    1st question: over the weekend I installed a Digitrax decoder in an older (posts on the board) Intermountain F7. The install went fine, I placed the loco on the track, punched in loco #3 and...
  17. Thread: Armored Trains

    by MRLdave
    Replies
    8
    Views
    510

    There are a bunch of 1/144 kits out there for a...

    There are a bunch of 1/144 kits out there for a german armoured train. This is the only one I could find on short notice ...
  18. Replies
    6
    Views
    304

    Thanks..........I could probably fix it, I looked...

    Thanks..........I could probably fix it, I looked at the tear down on Spookshow's site and it didn't look too bad, but I have no idea where to find parts for a FVM loco?
  19. Replies
    6
    Views
    304

    Fox Valley Hiawatha problem

    I couldn't find a thread on this, although I'm sure one exists............Is there a good spot to get a FVM 4-4-2 loco repaired? Or parts? I'm getting no response from Fox Valley, and I don't think...
  20. Replies
    13
    Views
    387

    This might work but might require a new...

    This might work but might require a new sign/decal https://www.microstru.com/Experimenter-Kits.html
  21. Replies
    15
    Views
    669

    Saw an article a while back (don't remember...

    Saw an article a while back (don't remember where) that was about being able to make the frame of the loco be the battery. So you wouldn't need to find room for the battery, it would just replace the...
  22. As far as roadnames, I've given up "hoping"...

    As far as roadnames, I've given up "hoping" .....at least Atlas has done a bunch of locos for small RR's, even if they don't always hit my favorites. Bachmann really drives me crazy.......I model...
  23. At the very least you need to remove all the...

    At the very least you need to remove all the numbers,logos,ect. No amount of primer will make those disappear......well if you use enough primer they will , but all the molded in details will also...
  24. Replies
    3
    Views
    495

    I have a 5 X 8 trailer I bought for hauling my...

    I have a 5 X 8 trailer I bought for hauling my (and club) NTRAK modules. I built one rack which holds 4' standard modules. It holds 3 modules and fits crossways in the front of the trailer. Then I...
  25. Replies
    9
    Views
    463

    As with most equipment, as newer stuff comes on...

    As with most equipment, as newer stuff comes on line, older equipment gets downgraded. So seeing heavyweights on a "name train" like the Empire Builder or a UP "Cities" train would not be very...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4