Search:

Type: Posts; User: jimbo.0455

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Happy Birthday!!! Enjoy...

    Happy Birthday!!! Enjoy...
  2. Replies
    11
    Views
    177

    Hi Ralph, here is a quick drawing of series vs....

    Hi Ralph, here is a quick drawing of series vs. parallel
  3. Happy Birthday!

    Happy Birthday!
  4. Replies
    23
    Views
    178

    Happy Birthday!

    Happy Birthday!
  5. Happy Birthday!!!

    Happy Birthday!!!
  6. Replies
    5
    Views
    184

    You can always move that lower siding up into the...

    You can always move that lower siding up into the yard and move the the outer loop to this spot. If you plan on running longer engines I would make the top section about 8-10 inches wider on the...
  7. Replies
    38
    Views
    2,785

    Sticky: Some very good points made, I would say to also...

    Some very good points made, I would say to also look to see if there is a MRR club in your area and hopefully in N Scale. This can be a great way for someone to learn about the hobby as well. Some...
  8. Happy Birthday !!!

    Happy Birthday !!!
  9. Thread: Name a town

    by jimbo.0455
    Replies
    71
    Views
    1,521

    Surprised I haven't seen it listed yet...

    Surprised I haven't seen it listed yet "Mooseport" from the 2004 movie "Welcome to Mosseport" with Gene Hackman and Ray Romano.
  10. Happy Birthday!!!

    Happy Birthday!!!
  11. Happy Birthday!!!

    Happy Birthday!!!
  12. Replies
    11
    Views
    435

    Well I know that the companies we deal with at...

    Well I know that the companies we deal with at work are staying shut down until at least Feb 9 due to the virus. That is a week + longer than they were supposed to be for CNY. At this point I would...
  13. Well Sad to report but I sold the layout. Posted...

    Well Sad to report but I sold the layout. Posted it to more to gain interest and was not expecting the amount of interest it generated from some very serious folks, The first person to come look at...
  14. Replies
    15
    Views
    465

    Leo have you tried to reach out to...

    Leo have you tried to reach out to Backdropwarehouse and see if they can recommend a good way? I am sure you are not the first person to have this issues, they may have a good way to do it. Just a...
  15. Replies
    33
    Views
    1,036

    Drive up window?

    Drive up window?
  16. Happy Birthday!!!

    Happy Birthday!!!
  17. Thanks Dave, but I have not done anything to it...

    Thanks Dave, but I have not done anything to it since this last photo...:( too many other things going on.
  18. Replies
    14
    Views
    390

    What about a square or rectangular hole punch...

    What about a square or rectangular hole punch from one of the craft stores? these are like the old round hole hand punch, it should work on thinner styrene.
  19. Happy Birthday!

    Happy Birthday!
  20. Sticky: Poll: Keep in mind it is not just the web site it is...

    Keep in mind it is not just the web site it is the equipment and maintenance of said equipment. It is not bad if it all works fine all the time but if/when there is a virus or a hardware issue that...
  21. Sticky: Poll: That sounds great! Run for a year and see were...

    That sounds great! Run for a year and see were you end up. We can revisit it then if needed. Thanks again for all the behind the scenes work to keep this going.
  22. Replies
    15
    Views
    353

    Glad it worked out for you, I would never had...

    Glad it worked out for you, I would never had thought to use the bench grinder I will next time... Thanks
  23. Replies
    15
    Views
    353

    Did the same thing last year, I used a small wire...

    Did the same thing last year, I used a small wire brush and water, let them soak for a bit and comb the wire brush down around the tree.
    It will get about 80-90% off then paint. If your lucky go...
  24. Looks Good, check out my version (link in Sig)

    Looks Good, check out my version (link in Sig)
  25. Replies
    6
    Views
    533

    Keep in mind any sealant (dull-coat or otherwise)...

    Keep in mind any sealant (dull-coat or otherwise) will tend to lighten any powders, so you may find you want to put it on slightly heavier to achieve the end result you are looking for. Some...
Results 1 to 25 of 319
Page 1 of 13 1 2 3 4