Search:

Type: Posts; User: gary60s

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. I went into an lhs to look at some N scale cars,...

    I went into an lhs to look at some N scale cars, when a couple of old HO scalers asked me why I was looking at that small sh-t. I thought, "how immature". When they started whispering and giggling,...
  2. https://www.nscale.net/forums/showthread.php?25889...

    https://www.nscale.net/forums/showthread.php?25889-Loco-truck-servicing
  3. Replies
    7
    Views
    552

    yes, as Daniel says, Download section, scenery...

    yes, as Daniel says, Download section, scenery tab, starting on middle of page 2.
  4. Replies
    290
    Views
    42,210

    Any cleaning solution should remove all traces of...

    Any cleaning solution should remove all traces of the NO-OX carrier, but not the NO-OX treatment of the rails.
  5. Not sure if this will work for you, but here are...

    Not sure if this will work for you, but here are some different control linkages for turnouts: https://www.nscale.net/forums/showthread.php?25904-Turnout-control-linkage
  6. Replies
    290
    Views
    42,210

    With all due respect Charles, you can not ruin a...

    With all due respect Charles, you can not ruin a layout with NO-OX. I suspect that you applied way,way,way too much. A thin almost microscopic application is not going to ruin a layout, in any case...
  7. Replies
    2
    Views
    66

    Article: Barn build

    You can view the page at https://www.nscale.net/forums/content.php?252-Barn-build
  8. Thread: Barn build

    by gary60s
    Replies
    2
    Views
    594

    Barn build

    Nine years ago I made this sketch set (https://www.nscale.net/forums/downloads.php?do=file&id=36), but never got around to building it. I know why I didn't, I knew the doors were gonna be tricky....
  9. Replies
    290
    Views
    42,210

    Update: Bar Mills no longer carries No-Ox.

    Update: Bar Mills no longer carries No-Ox.
  10. Replies
    18
    Views
    745

    https://www.nscale.net/forums/showthread.php?25435...

    https://www.nscale.net/forums/showthread.php?25435-Make-your-own-ballast-spreader
  11. Replies
    28
    Views
    2,228

    The clinging vine work is incredible !

    The clinging vine work is incredible !
  12. Micromark's corner punch at $35.00 is way too...

    Micromark's corner punch at $35.00 is way too expensive, but well worth it, for cutting window openings in sheet styrene.
  13. Replies
    15
    Views
    895

    I removed all the windows which was easy due to...

    I removed all the windows which was easy due to fact that they were all press fit with no glue. This was made possible because of the precision made openings with the Micromark corner punch. I have...
  14. Replies
    15
    Views
    895

    I made a big mistake on this one. Glued the...

    I made a big mistake on this one. Glued the acetate to the outside of windows instead of the inside. I may eventually remove them and do them over.
  15. Replies
    15
    Views
    895

    Forgot chimney. You can add one of your choice.

    Forgot chimney. You can add one of your choice.
  16. Replies
    15
    Views
    895

    Gluing turret walls to bottom of top floor...

    Gluing turret walls to bottom of top floor
    https://i.imgur.com/ssegPli.jpg

    Gluing turret bottoms to turret walls
    https://i.imgur.com/MGvffef.jpg

    Gluing on gable tops and turret roof supports...
  17. Replies
    15
    Views
    895

    building staircase (from RSLaserkits)...

    building staircase (from RSLaserkits)
    https://i.imgur.com/8wcnulA.jpg

    airbrushing walls
    https://i.imgur.com/6eRPyQB.jpg

    adding acetate to windows and doors
    https://i.imgur.com/Gdmbpob.jpg
    ...
  18. Replies
    15
    Views
    895

    parts template glued to styrene ready to cut out....

    parts template glued to styrene ready to cut out.
    https://i.imgur.com/6JxFFoO.jpg
  19. Replies
    7
    Views
    830

    It's from Micromark. 3/16" corner punch. Pricey...

    It's from Micromark. 3/16" corner punch. Pricey at $35.00, but I think its worth it.
  20. Replies
    7
    Views
    515

    Know nothing about them, but all 138 of my plans...

    Know nothing about them, but all 138 of my plans are free and they come with PDF's.
  21. Replies
    15
    Views
    895

    Not sure why I didn't do the original post here....

    Not sure why I didn't do the original post here. It's on trainboard.
  22. Replies
    15
    Views
    895

    Actually it was based on a christmas tree...

    Actually it was based on a christmas tree ornament!
  23. Replies
    15
    Views
    895

    petley depot build

    https://i.imgur.com/1SroNt8.jpg

    https://i.imgur.com/28x0FAt.jpg

    https://i.imgur.com/JglyXlm.jpg

    https://i.imgur.com/CcXdVjH.jpg
  24. tried to join there. captcha not working for me...

    tried to join there. captcha not working for me either.
  25. Replies
    7
    Views
    404

    Thanks to Bryan all is fixed.

    Thanks to Bryan all is fixed.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4