Search:

Type: Posts; User: Ender

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    122

    You can get a small wire stripper.

    You can get a small wire stripper.
  2. Replies
    11
    Views
    640

    No worries, Gryxter. At least you're smart...

    No worries, Gryxter. At least you're smart enough to ask the questions first. For some reason I always end up doing my own trial-and-error with every project I do. Gets expensive. :geek:
  3. Replies
    11
    Views
    640

    Gryxter, while your post should probably be...

    Gryxter, while your post should probably be broken off into its own thread, I think I can provide a little guidance:

    When you see LED strips listed, you'll see several specs. The size of the SMD...
  4. Replies
    9
    Views
    298

    Sorry, I don't remember where they're from but...

    Sorry, I don't remember where they're from but I've found good use from sets of wood pallets, stacks of cinder blocks, propane tanks, crossing gates, add-on details for vehicles, construction...
  5. Replies
    1
    Views
    196

    I do, but I'm not as picky about track as other...

    I do, but I'm not as picky about track as other details. I'm still fine with code 80. I figure once it's ballasted, it looks good enough to my eye.

    I try to keep it light though, with rust...
  6. Replies
    12
    Views
    356

    I make mine by mixing dry joint compound with...

    I make mine by mixing dry joint compound with powdered paints, then mixing a small batch with water and spreading where I want pavement. For dirt/gravel roads I use ARM dirt & powders. I like the...
  7. Replies
    9
    Views
    255

    Yes, it's a bit overscale for N but looks okay...

    Yes, it's a bit overscale for N but looks okay and is easy to work with. I dealt with the self-adhesive back on an irregular surface by using hot glue. That worked pretty good.

    You can see some...
  8. Replies
    29
    Views
    850

    I'm holding out for the 50 State Fish series.

    I'm holding out for the 50 State Fish series.
  9. Replies
    24
    Views
    590

    That's great. I like it. I want one. I...

    That's great. I like it.

    I want one. I dunno what for yet, but I want one. :D
  10. Replies
    24
    Views
    590

    I'd venture that you could. ...

    I'd venture that you could.

    https://www.nscale.net/forums/showthread.php?38659-Traveling-Bridge-Crane-for-P-amp-H

    Not too hard and kinda fun.
  11. Replies
    16
    Views
    3,262

    Sticky: Not on iOS, FileMaker Go doesn't support the...

    Not on iOS, FileMaker Go doesn't support the field mapping import dialog. But it can be done on a desktop using FileMaker Pro. Importing is also available in the RT version. (Use the Text File...
  12. Replies
    3
    Views
    128

    Wow. I just did a GIS of Interlaken, Switzerland...

    Wow. I just did a GIS of Interlaken, Switzerland and wow. What a beautiful area.
  13. Replies
    3
    Views
    128

    Very cool. I could see that getting a stucco...

    Very cool. I could see that getting a stucco finish for a southwestern look.
  14. Replies
    24
    Views
    590

    Any pics of what you have in mind?

    Any pics of what you have in mind?
  15. Replies
    18
    Views
    364

    Hey Steve. The type of structure may determine...

    Hey Steve.

    The type of structure may determine the best phasing for painting and installation. For lasercut buildings I usually paint the exterior and interior on the uncut sheets, the interior...
  16. Replies
    12
    Views
    997

    Oh that's just scratch built. I used a red LED...

    Oh that's just scratch built. I used a red LED (3mm?) and glued on some bits of tubing for the four shrouds, then painted the outside silver then black. I have it hooked to a blinking circuit for...
  17. Replies
    12
    Views
    997

    It's kinda sad really. Those guys have been...

    It's kinda sad really. Those guys have been working on that building for like 10 years.
  18. Replies
    7
    Views
    253

    You worried your shades of rust won't match?...

    You worried your shades of rust won't match? :rolleyes:
  19. Replies
    8
    Views
    425

    Easy tip: a light block can be a simple diagonal...

    Easy tip: a light block can be a simple diagonal sheet of black paper or styrene that cuts across the inside of the building, giving you two lighting zones (perhaps a lit side and a dark side.) Or...
  20. Replies
    9
    Views
    288

    Different shade, but here's WS version: ...

    Different shade, but here's WS version: https://woodlandscenics.woodlandscenics.com/show/category/PolyFiber

    Also comes with some of their tree kits.
  21. Replies
    10
    Views
    432

    I didn't have very good luck with grout or WS...

    I didn't have very good luck with grout or WS ballast. But then I discovered Arizona Rock & Mineral stuff. That's da bomb.

    https://live.staticflickr.com/7428/8982727876_890ef4c3f7_c.jpg
    ...
  22. I like this Faller glue too.

    I like this Faller glue too.
  23. Replies
    13
    Views
    627

    Time seems to move faster as you get older.

    Time seems to move faster as you get older.
  24. Replies
    12
    Views
    440

    I second the ivy. Weathering (and ivy) can cure...

    I second the ivy. Weathering (and ivy) can cure all.
  25. Thread: dead leaves

    by Ender
    Replies
    17
    Views
    523

    I think it looks okay. Just needs more of it...

    I think it looks okay. Just needs more of it under the trees.

    My ground foam mix is overscale too, but the overall picture works when everything is built up:
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4