Page 2 of 2 FirstFirst 12
Results 21 to 28 of 28

Thread: Kato Locos vs. Bachmann E-Z track

  1. #21
    Join Date
    Jan 2016
    Posts
    29
    Thanks
    41
    Thanked 65 Times in 10 Posts
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default

    Nope, you haven't lost me. Just an update - I pulled a couple of my old Kato Mikados from my "archives" and gave them a run on my E-Z-Track. To my surprise, they ran great with no derail problems whatsoever - even through the turn outs. Over the weekend I received a used Kato EMD SD 45 loco. I tested it as well and low and behold it also had no derail problems. I'm beginning to think that my problems with the 2 locos I first mentioned might be the loco's trucks and not the track. Anyway, long story short - I'm going with the majority here and I ordered a Kato M2 starter set and some extra track pieces. Thanks again for all the input. Smitty

  2. The Following 7 Users Say Thank You to smittykid For This Useful Post:


  3. #22
    Join Date
    Feb 2013
    Location
    Sequim, WA
    Posts
    2,294
    Blog Entries
    1
    Thanks
    7,757
    Thanked 3,054 Times in 1,288 Posts
    Mentioned
    70 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by smittykid View Post
    , long story short - I'm going with the majority here and I ordered a Kato M2 starter set and some extra track pieces. Thanks again for all the input. Smitty
    But do invest in an N scale NMRA standards gauge. It's kinda one of those some-day-you-will-thank-me/us things. $12 and it saves a lot of headaches down the road.

  4. #23
    Join Date
    Apr 2010
    Location
    Victoria, BC, Canada
    Posts
    7,292
    Blog Entries
    1
    Thanks
    5,997
    Thanked 12,213 Times in 3,046 Posts
    Mentioned
    77 Post(s)
    Tagged
    0 Thread(s)

    Default

    Yeah I had 12 brand new atlas turnouts installed on my layout and tested everything with 2 of my most fussy locos. Later though running some other locos I found they consistently derailed at the same turnout every time. Was it their wheels? The turnout? Something else? With my NMRA gauge I was able to see the points on the turnout were like 0.25mm off AND the wheels on a couple of these locos were a tiny tiny bit out of gauge the other way, which combined to cause the problem. The gauge is a real essential tool to have.

  5. The Following 2 Users Say Thank You to baronjutter For This Useful Post:


  6. #24
    Join Date
    Feb 2013
    Location
    Sequim, WA
    Posts
    2,294
    Blog Entries
    1
    Thanks
    7,757
    Thanked 3,054 Times in 1,288 Posts
    Mentioned
    70 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Paul Schmidt View Post
    and it saves a lot of headaches down the road.
    Yeah, I'm a chump for quoting myself. ...

    I said the NMRA standards gauge saves headaches. It does.

    It can also be associated with a headache, viz. "Where did I leave that doggone gauge now!"

  7. The Following 2 Users Say Thank You to Paul Schmidt For This Useful Post:


  8. #25
    Join Date
    Feb 2019
    Posts
    52
    Thanks
    17
    Thanked 21 Times in 10 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default

    I have a layout I'm working on, the Kato Amherst 2005, slightly modified.
    I't's mainly modified because I also wanted to use my existing Bachman EZ track, so the inner loop is Bachman and the rest is Kato unitrack.

    It took a bit of fiddling but they are now playing nice together.
    I had a little trouble with one Bachman steamer but that is all fixed now. (The frogs on the Bachman track are sometimes a bit higher than the Kato turnouts.)

    I have already made a pact with myself to buy only Kato track from now on, as the quality difference is obvious, but the Bachman track is still quite usable.
    To join the two types is just a matter of pulling off the connector clips on the Kato track (an easily reversible option), and cutting of the plastic protrusions on the Bachman
    connectors with a razor saw (not a reversible option), and then using standard track joiners, in this case code 100.

    The tracks line up well in most cases, you might have to do a bit filing at the joints occasionally, but it can be done.

    BTW, I paid $39.00 each for my Bachman turnouts, and but only $29.00 for the Kato units.
    If you shop around you can find pretty good deals on Kato track for the most part.

    So smittykid, don't let us discourage you from using what you have.
    If you are on a strict budget, make do, and learn from it.

    As for the derailing, I had a problem with one or two pieces of rolling stock derailing on turnouts.
    On close inspection with a flashlight during VERY slow motion through turnouts, I was able to ascertain that one truck in particular when being pushed through the turnout was
    catching on the INSIDE of the open turnout rail because the wheels were too close to each other (out of gauge), so I turned the unit upside down and applied some gentle pressure
    to the inside of the wheels to make them track just a little bit wider and voila!
    No more derailing! Sometimes it's that simple.
    I didn't have an nmra gauge at the time, but one is on order now.

  9. #26
    Join Date
    Feb 2019
    Posts
    52
    Thanks
    17
    Thanked 21 Times in 10 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Paul Schmidt View Post
    Yeah, I'm a chump for quoting myself. ...

    I said the NMRA standards gauge saves headaches. It does.

    It can also be associated with a headache, viz. "Where did I leave that doggone gauge now!"
    Is it steel? if so, stick a magnet on it and attach it somewhere safe.

  10. The Following User Says Thank You to lilleyen For This Useful Post:


  11. #27
    Join Date
    Jun 2014
    Posts
    538
    Thanks
    35
    Thanked 498 Times in 260 Posts
    Mentioned
    17 Post(s)
    Tagged
    0 Thread(s)

    Default

    I need an 'embarrasssed' and 'chagrin' emoticon.

    I have two gauges.
    I keep them together in the same envelope.

    It is not exactly that I lost one ... I know it is in here somewhere...
    it is that I needed it at that time.

    when I 'lose' one now, I guard the second one carefully until the first surfaces.

    I've been known to lose whole locos also...

    victor

  12. The Following User Says Thank You to victor miranda For This Useful Post:


  13. #28
    Join Date
    Jun 2013
    Location
    Mill Bay BC
    Posts
    2,711
    Thanks
    4,500
    Thanked 3,670 Times in 1,377 Posts
    Mentioned
    72 Post(s)
    Tagged
    1 Thread(s)

    Default

    Quote Originally Posted by Paul Schmidt View Post
    "Where did I leave that doggone gauge now!"
    I've lost and found mine more times than i can remember . Its gotten to the point that its like getting a gift everytime it turns up . Having a bit of a forgetful mind does have its little pleasures lol

    Steve

  14. The Following 2 Users Say Thank You to aflica For This Useful Post:


Similar Threads

  1. Replies: 2
    Last Post: 5th Jan 2018, 11:38 PM
  2. Bachmann steam locos garbage?
    By brad4321 in forum Steam
    Replies: 38
    Last Post: 15th Mar 2015, 03:47 PM
  3. Replies: 7
    Last Post: 18th Sep 2014, 02:02 AM
  4. Mixing track - Kato, Bachmann, Atlas 80
    By Jonkv in forum Trackage
    Replies: 17
    Last Post: 23rd Sep 2013, 05:30 AM
  5. Kato locos & Atlas track
    By SpecialK67 in forum Diesel
    Replies: 11
    Last Post: 9th Nov 2012, 09:52 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •