Results 1 to 7 of 7

Thread: Help needed decoder install MT FT A&B

  1. #1
    Join Date
    Mar 2014
    Location
    Riverview NB
    Posts
    13
    Thanks
    5
    Thanked 3 Times in 2 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Help needed decoder install MT FT A&B

    As suggested on the Digitrax decoder list, I am using Digitrax DN163M0 decoders in both my A and B Micro train FT units. On both locos, I cannot get the shells back on - the decoder is in the way.

    Any suggestions would be appreciated.

  2. #2
    Join Date
    Aug 2014
    Location
    Ft. Worth, Texas, USA
    Posts
    371
    Thanks
    1,028
    Thanked 448 Times in 227 Posts
    Mentioned
    17 Post(s)
    Tagged
    0 Thread(s)

    Default

    This might help, says F7 but it looks like an FT. Towards the end he describes getting the shell back on. https://www.youtube.com/watch?v=iewd1yYEF_8
    Radon Gulch & Tortilla Flats Railway - the 'Good Gas' line! - a minor division of the Santa Fe Southern Railway Co. "Dust, gas and a lot of rocky stuff...

  3. #3
    Join Date
    May 2012
    Location
    Twin Cities, Minnesota
    Posts
    1,820
    Thanks
    964
    Thanked 4,998 Times in 1,051 Posts
    Mentioned
    156 Post(s)
    Tagged
    0 Thread(s)

    Default

    I don't recall having any problems getting the shells back on mine. Do the decoders still look like this?



    -Mark

  4. The Following User Says Thank You to Spookshow For This Useful Post:


  5. #4
    Join Date
    May 2007
    Location
    Phoenix, AZ
    Posts
    743
    Thanks
    8
    Thanked 212 Times in 158 Posts
    Mentioned
    7 Post(s)
    Tagged
    1 Thread(s)

    Default

    Be a while that I have done one of these. Has I recall there are some obstructions on the inside of the shell that fit into the place where that decoder sits. Try putting some modeling clay on the inside of the shell where the decoder should touch.
    then try to put the shell on. When it will not attach all the way- remove shell and look to see where the decoder is hitting the clay. Re move clay and then relive the places the clay was displaced.

  6. #5
    Join Date
    May 2012
    Location
    Twin Cities, Minnesota
    Posts
    1,820
    Thanks
    964
    Thanked 4,998 Times in 1,051 Posts
    Mentioned
    156 Post(s)
    Tagged
    0 Thread(s)

    Default

    The plastic inserts for the portholes are pretty thick, but a modicum of force should get them past the decoder. Or at least it did for me. They're a much bigger annoyance when trying to get the shell off (which I just discovered, lol). You could try sanding them a bit thinner if you're worried about hurting something.

    -Mark

  7. #6
    Join Date
    Mar 2014
    Location
    Riverview NB
    Posts
    13
    Thanks
    5
    Thanked 3 Times in 2 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Thumbs up Install done.

    I contacted my friend Jean and he ended up doing the install for me. The Digitrax decoder was 14.75 mm across, and the original board was 13.2 mm. He ended up sanding .25 mm off each side of the decoder, and .5 mm off each side of the windows. I have JPG pictures, but when I try to upload, I get a "upload failed" response. Anyone have any suggestions?

    Thanks to everyone who replied - drbnc, Mark and woodone.


  8. #7
    Join Date
    Feb 2013
    Posts
    3,183
    Blog Entries
    1
    Thanks
    10,551
    Thanked 4,806 Times in 1,891 Posts
    Mentioned
    103 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Chaos Railway View Post
    when I try to upload, I get a "upload failed" response. Anyone have any suggestions?
    You probably just need to resize your photos.

Similar Threads

  1. First decoder install!
    By ranulf in forum DCC
    Replies: 8
    Last Post: 22nd Dec 2011, 03:33 AM
  2. Decoder help needed
    By darticus in forum DCC
    Replies: 3
    Last Post: 18th Feb 2011, 08:45 PM
  3. First Decoder Install ???
    By JohnMD in forum DCC
    Replies: 6
    Last Post: 22nd Jul 2010, 08:04 AM
  4. help with first decoder install
    By playak47 in forum DCC
    Replies: 10
    Last Post: 5th May 2007, 10:08 PM
  5. Which decoder and how to install?
    By nycolin in forum DCC
    Replies: 3
    Last Post: 29th Apr 2007, 09:50 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •